Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя | Manualshive

Страница: 215 / 270

background image

host1(config-subif)#

ipv6 mld apply-oif-map OIFMAP

■

Use the

no

version to remove the outgoing interface map association from the

interface.

■

See ipv6 mld apply-oif-map.

ipv6 mld oif-map

■

Use to create an OIF map.

■

Use the MLD-OIF-Map-Name RADIUS attribute (VSA 26-76) in RADIUS
Access-Accept messages as an alternative method of configuring this value.

■

Example

host1(config)#

ipv6 mld oif-map OIFMAP atm 3/0.1 ff0e::1:1/128 2001::1:1/128

host1(config)#

ipv6 mld oif-map OIFMAP atm 3/0.2 ff0e::1:1/128 2001::1:1/128

host1(config)#

ipv6 mld oif-map OIFMAP atm 3/0.3 ff0e::1:1/128

host1(config)#

ipv6 mld oif-map OIFMAP atm 3/0.4 ff0e::1:0/112 2001::1:1/128

host1(config)#

ipv6 mld oif-map OIFMAP atm 3/0.5 ff0e::1:0/112 2001::1:1/128

host1(config)#

ipv6 mld oif-map OIFMAP self ::/0 2001::1:0/112

■

Use the

no

version to remove an outgoing interface map attribute.

■

See ipv6 mld oif-map.

ipv6 mld version

■

Use to set the MLD version (1 or 2) for the interface or specify a passive interface
with only multicast-data-forwarding capability (passive).

■

Use the MLD-Version RADIUS attribute (VSA 26-77) in RADIUS Access-Accept
messages as an alternative method of configuring this value.

■

Example

host1:dallas(config-if)#

ipv6 mld version passive

■

Use the

no

version to set the version to the default, mldv2.

■

See ipv6 mld version.

Configuring SSM Mapping

SSM mapping enables the router to determine one or more source addresses for
group G. The mapping effectively translates an MLDv1 multicast listener report to
an MLDv2 report, enabling the router to continue as if it had initially received an
MLDv2 report. After the router is joined to these groups, it sends out PIM join
messages and continues to enable joining from these groups, as long as it continues
to receive MLDv1 membership reports and no change occurs to the SSM mapping
for the group.

When you statically configure SSM mapping, the router can discover source addresses
from a statically configured table.

Configuring SSM Mapping

■

193

Chapter 6: Configuring Multicast Listener Discovery

«
...
213
214
215
216
217
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

AccuSync LCD52V

Бренд: NEC Страницы: 5

Бренд: AMX Страницы: 212

TEMS VISUALIZATION 7.2 ENTERPRISE

Бренд: ASCOM Страницы: 8

IFOLDER 3 - ADMINISTRATION

Бренд: Novell Страницы: 148

Electric Bass Vol. 1—Rock

Бренд: M-Audio Страницы: 4

Бренд: Epson Страницы: 6

Stylus Color 600Q

Бренд: Epson Страницы: 1

Stylus Pro - Stylus Color Pro Ink Jet Printer

Бренд: Epson Страницы: 14

Software Film Factory

Бренд: Epson Страницы: 73

Stylus Pro - Stylus Color Pro Ink Jet Printer

Бренд: Epson Страницы: 98

Stylus Color 600Q

Бренд: Epson Страницы: 95

Бренд: Epson Страницы: 209

PowerLite D6150

Бренд: Epson Страницы: 196

Skyport Communications

Бренд: Venstar Страницы: 41

BACKUP EXEC 11D

Бренд: Symantec Страницы: 18

ALTIRIS IT MANAGEMENT SUITE 7.0 MR2 - S

Бренд: Symantec Страницы: 14

ALTIRIS DEPLOYMENT SOLUTION 7.1

Бренд: Symantec Страницы: 90

9235 - Coolscan III

Бренд: Nikon Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды