manualshive.com logo in svg

Juniper JUNOSE 11.1.X MULTICAST ROUTING, Руководство по настройке

Конфигурационное руководство Juniper JUNOSE 11.1.X MULTICAST ROUTING доступно для бесплатного скачивания на нашем сайте. Это подробное руководство поможет вам освоить настройку и использование продукта. Посетите manualshive.com чтобы получить доступ к этому полезному ресурсу.

Поделиться
Скачать
background image

■

Use to disable RPF checks for specified (S,G) pairs.

■

Specify a standard IPv6 access list that defines the (S,G) pairs.

■

Example

host1(config)#

ipv6 multicast-routing disable-rpf-check denver-list

■

Use the 

no

 version to restore the default situation, in which the router performs

RPF checks for all (S,G) pairs.

■

See ipv6 multicast-routing disable-rpf-check.

Using Unicast Routes for RPF

You can use the 

ip route-type

 command to specify that BGP routes should be available

for RPF. Routes available for RPF appear in the multicast view of the routing table.

NOTE:

This command functions the same for both IPv4 and IPv6 multicast.

ipv6 route-type

■

Use to specify that BGP routes are available only for unicast forwarding, only for
multicast RPF checks, or for both.

■

Use the 

show ipv6 rpf-routes

 command to view the routes available for RPF.

■

By default, BGP routes are available both for unicast forwarding and multicast
reverse-path forwarding checks.

■

Example

host1(config)#

router bgp

host1(config-router)#

ipv6 route-type multicast

■

There is no 

no

 version.

■

See ipv6 route-type.

Defining Permanent IPv6 Multicast Forwarding Entries

An mroute is a multicast traffic flow, a (Source, Group) entry used for forwarding
multicast traffic). By default, forwarding mroutes (with a valid RPF incoming interface)
are timed out if data for them is not received for 210 seconds. However, you can
specify an mroute as permanent by using the 

ipv6 multicast-routing

permanent-mroute 

command.

ipv6 multicast-routing permanent-mroute

■

Use to specify that any newly created mroutes that match the specified access-list
do not time out.

■

Using this command does not change existing mroutes.

Using Unicast Routes for RPF

■

153

Chapter 5: Configuring IPv6 Multicast

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

Waves Linear-Phase MultiBand Software Audio Processor User Manual preview
Linear-Phase MultiBand Software Audio Processor
Бренд: Waves Страницы: 27
AVIRA ANTIVIR VIRUS SCAN ADAPTER Configuration preview
ANTIVIR VIRUS SCAN ADAPTER
Бренд: AVIRA Страницы: 29
Alcatel-Lucent Wireless Network Guardian 9900 Brochure preview
Wireless Network Guardian 9900
Бренд: Alcatel-Lucent Страницы: 2
Tandberg Data IBM LOTUS NOTES-DOMINO V 11.3 - INSTALLATION AND ... Integration Manual preview
IBM LOTUS NOTES-DOMINO V 11.3 - INSTALLATION AND ...
Бренд: Tandberg Data Страницы: 49
Ricoh GlobalScan NX Server 5/Server 32/Server 750 Manual preview
GlobalScan NX Server 5/Server 32/Server 750
Бренд: Ricoh Страницы: 6
Novell DATA SYNCHRONIZER - UPDATE 1 Installation Manual preview
DATA SYNCHRONIZER - UPDATE 1
Бренд: Novell Страницы: 9
Aastra MX-ONE 4.2 User Manual preview
MX-ONE 4.2
Бренд: Aastra Страницы: 46
MACROMEDIA FLASH 8-ACTIONSCRIPT 2.0 LANGUAGE Reference preview
FLASH 8-ACTIONSCRIPT 2.0 LANGUAGE
Бренд: MACROMEDIA Страницы: 1378
ArcSoft DV-6400 Quick Start Manual preview
DV-6400
Бренд: ArcSoft Страницы: 6
Juniper TePM Agent Release Note preview
TePM Agent
Бренд: Juniper Страницы: 9
Intel SMALL BUSINESS SERVER Manual preview
SMALL BUSINESS SERVER
Бренд: Intel Страницы: 79
FieldServer FS-8700-52 Driver Manual preview
FS-8700-52
Бренд: FieldServer Страницы: 17
Bay Networks Multilink PPP Administrator'S Manual preview
Multilink PPP
Бренд: Bay Networks Страницы: 22
Oce XMPie User Manual preview
XMPie
Бренд: Oce Страницы: 22
IBM VIAVOICE 3-FOR MAC OS X User Manual preview
VIAVOICE 3-FOR MAC OS X
Бренд: IBM Страницы: 96
Raritan Paragon Manager User Manual preview
Paragon Manager
Бренд: Raritan Страницы: 24
AVG IDENTITY PROTECTION User Manual preview
IDENTITY PROTECTION
Бренд: AVG Страницы: 27
Harrison MIXBUS V2.0.2 User Manual preview
MIXBUS V2.0.2
Бренд: Harrison Страницы: 85

Бренды по названию

Популярные бренды

Загрузить еще бренды