Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 270

background image

Each port on the I/O module or IOA displayed in Figure 18 on page 162 has two
queues. These queues are further down the egress path than the queues found on
the line module and populated by the FC.

The low-priority queue is dedicated to packets that are received from the line module
queues that are dedicated to the physical ports. This queue blocks when full and
provides backpressure to the line module. This queue services unicast and multicast
traffic that is not using the hardware multicast packet replication feature.

The high-priority queue is dedicated to packets that are received from the line module
queue for port 8. This queue is serviced at a higher priority than the first queue, and
drops packets when full.

For more information about high-density Ethernet, see

Configuring Ethernet Interfaces

in

JUNOSe Physical Layer Configuration Guide

.

Supported Modules and Encapsulations

You can enable optimized multicast packet replication on port 8 of the following
high-density Ethernet modules:

■

GE-8 I/O module (pairs with the GE-HDE line module)

■

ES2-S1 GE-8 IOA (pairs with the ES2 4G LM and the ES2 10G LM)

When enabled, the optimized multicast packet replication feature defines the
encapsulation of the egress multicast packet. The following encapsulations are
supported:

■

IPv6 over Gigabit Ethernet

■

IPv6 over VLAN

■

IPv6 over S-VLAN

NOTE:

802.3ad link aggregation group (LAG) bundles do not support optimized

multicast packet replication.

The optimized multicast packet replication feature also provides an interface over
which you can configure the following:

■

IP MTU

■

Ethernet MTU

■

Egress IP policy

■

Egress VLAN policy

■

QoS

Configuring Hardware Multicast Packet Replication

■

163

Chapter 5: Configuring IPv6 Multicast

«
...
183
184
185
186
187
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

Бренд: Partec Страницы: 98

Бренд: AMX Страницы: 54

Advanced Calculator 2.2

Бренд: CDML Страницы: 48

DEVICE FILTER MAC

Бренд: FARONICS Страницы: 30

CLUSTER SUITE - FOR RHEL 4

Бренд: Red Hat Страницы: 74

SYSMAC CX-Programmer 9

Бренд: Omron Страницы: 232

Бренд: EverFocus Страницы: 44

Бренд: LEI Extras Страницы: 80

Бренд: FieldServer Страницы: 14

Pro Tools M-Powered

Бренд: DigiDesign Страницы: 22

Бренд: YOKOGAWA Страницы: 29

VIRUS|POWERCORE

Бренд: Access Страницы: 124

FreeFlow 701P45570

Бренд: Xerox Страницы: 12

Бренд: Canon Страницы: 102

Бренд: Omron Страницы: 2

Бренд: Omron Страницы: 7

Бренд: Omron Страницы: 2

CX-ONE - BROCHURE 1

Бренд: Omron Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды