Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 270

background image

host1:boston(config-if)#

ip dvmrp announce-filter boston-list

■

Use the

no

version to enable the interface to advertise all DVMRP routes that it

has learned.

■

See ip dvmrp announce-filter.

Preventing Dynamic Route Distribution

By default, if you make changes to a route map, the router dynamically redistributes
the routes in DVMRP. To prevent this dynamic redistribution, use the

disable-dynamic-redistribute

command.

disable-dynamic-redistribute

■

Use to halt the dynamic redistribution of routes that are initiated by changes to
a route map; dynamic redistribution is enabled by default.

■

Example

host1(config-router)#

disable-dynamic-redistribute

■

There is no

no

version.

■

See disable-dynamic-redistribute.

Exchanging DVMRP Unicast Routes

DVMRP maintains its own unicast routing table, based on distance vector calculations.
The routing table defines the best-known distance to each destination and how to
get there. The router updates the table by exchanging information with its neighbors.
The DVMRP routing table is used solely for RPF lookups.

By default, if DVMRP owns an interface, that interface exchanges DVMRP unicast
routes with its neighbors, and you cannot disable the exchange of routes. However,
you can enable and disable the exchange of DVMRP unicast routes on interfaces that
DVMRP does not own.

When an interface exchanges DVMRP routes, the router obtains routes from DVMRP
report messages and stores them in its DVMRP routing table. Other multicast
protocols, such as PIM, can then use these routes for RPF lookups. With this feature,
PIM can use the DVMRP routing table even when the router is not running DVMRP.

All interfaces, including tunnels, support DVMRP unicast routing. DVMRP tunnels
use DVMRP multicast routing to support DVMRP unicast routing.

ip dvmrp unicast-routing

■

Use to enable the exchange of DVMRP unicast routes on an interface not owned
by DVMRP.

■

Example

host1:boston(config-if)#

ip dvmrp unicast-routing

134

■

Preventing Dynamic Route Distribution

JUNOSe 11.1.x Multicast Routing Configuration Guide

«
...
154
155
156
157
158
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

Бренд: Garmin Страницы: 8

DEEP FREEZE - INTEGRATING WITH NOVELL ZENWORKS...

Бренд: FARONICS Страницы: 23

CONTRIBUTE-USING CONTRIBUTE

Бренд: MACROMEDIA Страницы: 214

Бренд: Palm Страницы: 22

CERTIFICATE 8.0 RELEASE NOTES

Бренд: Red Hat Страницы: 34

CERTIFICATE SYSTEM 7.3 - ADMINISTRATION

Бренд: Red Hat Страницы: 554

Бренд: FieldServer Страницы: 11

15606-011408-9320 - MAP R6.3 CPU MODEL-UPG 4/5 MIN 2 CPUS INITL

Бренд: Autodesk Страницы: 190

00308-011408-9F30A - VLA AUTOSKETCH R8-MEDIA W9X/NT

Бренд: Autodesk Страницы: 400

MEDIASTUDIO PRO 8.0 - SMART COMPOSITOR...

Бренд: Ulead Страницы: 308

Бренд: Magellan Страницы: 14

VIAVOICE-SIMPLY DICTATION FOR MAC OS X

Бренд: IBM Страницы: 92

Parallels Desktop 4.0

Бренд: Parallel Страницы: 2

EDIUS - INSTALLATION V6.0

Бренд: GRASS VALLEY Страницы: 23

PowerLite 1775W

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 6

Бренд: Epson Страницы: 193

Бренд: Epson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды