Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 270

background image

Table 5: IGMP Commands

(continued)

ip igmp static-include

ip igmp last-member-query-interval

ip igmp version

ip igmp promiscuous

multicast group port limit

ip igmp querier

ip igmp querier-timeout

The following sections describe the tasks associated with these and other

ip igmp

commands.

You can also use various IGMP-specific RADIUS attributes in RADIUS Access-Accept
messages as an alternative method of configuring certain values. See

Configuring

RADIUS Attributes

in the

JUNOSe Broadband Access Configuration Guide

for additional

information.

Enabling IGMP on an Interface

You must start IGMP on each interface that you want to use the protocol. You can
configure IGMP and either PIM or DVMRP on the same interface. If you configure
only IGMP on an interface, IGMP owns that interface. If you configure IGMP and
either PIM or DVMRP on an interface, PIM or DVMRP owns the interface.

By enabling IGMP, the router processes incoming multicast packets and creates an
entry in the multicast routing table. If neither PIM nor DVMRP own the interface (for
example, when only IGMP is configured), then the packets are locally routed to other
interfaces on the router. PIM or DVMRP must be configured on the interface for
packets to be sent to other routers.

For networks that use only IGMPv1, you can configure an interface to operate in
IGMPv1 mode. However, IGMPv2 and IGMPv3 interfaces support IGMPv1 hosts. In
an IGMPv1 network, you must configure one interface to act as a querier. In an
IGMPv2 or IGMPv3 network, the querier is the router with the lowest IP address.

To start IGMP, complete the following steps:

1.

Enable IGMP on the interface (IGMPv2 is the default version).

2.

(IGMPv1 or IGMPv3) Specify the IGMP version for the interface.

3.

(IGMPv1 only) Specify that the interface act as the querier for the network.

ip igmp

■

Use to enable IGMP on an interface and to set the IGMP version to IGMPv2. Use
the

ip igmp version

command to specify a different IGMP version.

■

Example

host1:boston(config-if)#

ip igmp

48

■

Enabling IGMP on an Interface

JUNOSe 11.1.x Multicast Routing Configuration Guide

«
...
68
69
70
71
72
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

Бренд: MACROMEDIA Страницы: 292

Бренд: MACROMEDIA Страницы: 26

Бренд: MACROMEDIA Страницы: 32

Бренд: UMAX Technologies Страницы: 10

Бренд: Davis Instruments Страницы: 108

8.5 ANTI-VIRUS - LINUX-FREEBSD REV 85.2

Бренд: AVG Страницы: 234

COLDFUSION 5 - INSTALING AND CONFIGURING...

Бренд: MACROMEDIA Страницы: 160

Бренд: Spectrel Страницы: 74

Simotion A4027118-A0414

Бренд: Siemens Страницы: 107

Gigaset talk & surf 6.0

Бренд: Siemens Страницы: 188

AutoCAD Civil 3D 2013

Бренд: Autodesk Страницы: 25

Бренд: Autodesk Страницы: 12

235B1-05A761-1301 - AutoCAD MEP 2010

Бренд: Autodesk Страницы: 878

Бренд: Autodesk Страницы: 1490

Network HotSync

Бренд: 3Com Страницы: 38

QConvergeConsole CLI 2400 Series

Бренд: Qlogic Страницы: 366

DocuPrint 100MX

Бренд: Xerox Страницы: 74

PowerCore Master X3

Бренд: TC Electronic Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды