Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя | Manualshive

Страница: 190 / 270

background image

Use the show ipv6 interface command to display statistics for an IPv6 interface
configured over port 8. For more information, see

Monitoring IPv6

in

JUNOSe IP, IPv6,

and IGP Configuration Guide

.

Multicast traffic redirected by the hardware multicast packet replication feature is
displayed in the statistics for the IPv6 or VLAN interface over port 8, not the original
IP or VLAN interface over the physical port.

The statistics for the IPv6 or VLAN interface over port 8 reflect the number of packets
that passed through this interface destined for the hardware multicast packet
replication hardware. These statistics have no direct correlation to the number of
packets being transmitted from any of the physical ports.

MLD Statistics

Use the show ipv6 mld interface command to display statistics, including hardware
multicast packet replication status, for an IPv6 interface stacked over port 8. For
more information, see “Monitoring MLD” on page 199 in “Configuring Multicast
Listener Discovery” on page 183.

Blocking and Limiting Multicast Traffic

You can either block mroute creation, limit the multicast bandwidth admitted on an
outgoing interface, or limit outgoing interface creation on a port.

Blocking Mroutes

By default, when an interface receives multicast traffic, even when the scope of that
traffic exceeds link-local, the virtual router creates an mroute. You can use the

ipv6

block-multicast-sources

command to block all multicast traffic with a scope larger

than link-local (for example, global) and prevent mroute creation under these
conditions.

NOTE:

Issuing this command does not affect reception of link-local multicast packets.

ipv6 block-multicast-sources

■

Use to prevent mroute creation by blocking multicast traffic that has a scope
larger than link-local (for example, global).

■

Example

host1(config)#

ipv6 block-multicast-sources

■

Use the

no

version to restore the default behavior of creating mroutes on receiving

multicast packets.

■

See ipv6 block-multicast-sources.

168

■

Blocking and Limiting Multicast Traffic

JUNOSe 11.1.x Multicast Routing Configuration Guide

«
...
188
189
190
191
192
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

imagePROGRAF W6400

Бренд: Canon Страницы: 84

COLDFUSION MX 61-CFML

Бренд: MACROMEDIA Страницы: 34

DocuColor 45054549

Бренд: Xerox Страницы: 30

JUNOS PUS MOBILE SECURITY SUITE

Бренд: Juniper Страницы: 6

Бренд: Nortel Страницы: 374

Бренд: Altigen Страницы: 502

Бренд: Oce Страницы: 22

7C03 MMAC SmartSWITCH

Бренд: Cabletron Systems Страницы: 150

Бренд: ICP Страницы: 8

Security Threat Response Manager

Бренд: Juniper Страницы: 10

Nuvi 780 - Automotive GPS Receiver

Бренд: Garmin Страницы: 14

Бренд: NEC Страницы: 27

Digital Signage

Бренд: NEC Страницы: 29

Бренд: NEC Страницы: 119

Бренд: NEC Страницы: 58

DiamondPro 2070SB

Бренд: NEC Страницы: 66

ExpressCluster SRE

Бренд: NEC Страницы: 129

Display Wall Calibrator 1.0.00

Бренд: NEC Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды