Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 270

background image

NOTE:

A PIM router can receive group-to-RP mappings from either BSR or auto-RP,

but not from both. Because BSR and auto-RP use different mapping algorithms, the
mechanisms cannot coexist.

NOTE:

Static-override is configured using the override switch in the

ip pim rp-address

command.

CAUTION:

The maps distributed by BSR and Auto-RP for the same RP announcements

may be different. Because the Auto-RP mapping agent resolves mapping conflicts,
a PIM router that applies the BSR mapping algorithm to an Auto-RP distributed map
should produce the same result as a router that applies the Auto-RP mapping
algorithm. However, the reverse is not true. A PIM router that applies the BSR mapping
algorithm to a BSR distributed map may produce a different result to a router that
applies the Auto-RP mapping algorithm. This means that

a PIM IPv4 domain can

operate either BSR or Auto-RP

.

PIM Sparse-Dense Mode

In PIM sparse-dense mode, if an RP is not known for a group, the router sends data
using PIM dense mode. However, if the router discovers an RP or you configure an
RP statically, PIM sparse mode takes over.

You can configure both PIM dense mode and PIM sparse mode commands in PIM
sparse-dense mode.

PIM Source-Specific Multicast

PIM SSM is an extension of the PIM protocol. Using SSM, a client can receive multicast
traffic directly from the source. PIM SSM uses PIM sparse mode functionality to create
an SPT between the client and the source, but builds the SPT without using an RP.

By default, the SSM group multicast address is limited to the IP address range
232.0.0.0 to 232.255.255.255. You can use the

ip pim ssm

command to extend

SSM operations into another Class D range. (See “Configuring PIM SSM” on page 106.)

An SSM-configured network has the following advantages over a traditionally
configured PIM sparse mode network include the following:

■

No need for shared trees or RP mapping (no RP is required).

■

No need for RP-to-RP source discovery through Multicast Source Discovery
Protocol (MSDP).

Overview

■

85

Chapter 3: Configuring PIM for IPv4 Multicast

«
...
105
106
107
108
109
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

Бренд: TANDBERG Страницы: 66

Content Server None

Бренд: TANDBERG Страницы: 14

FLEXXPECT-PHARMA

Бренд: Omron Страницы: 2

NETWORK SATELLITE SERVER 4.0.5

Бренд: Red Hat Страницы: 82

NETWORK BASIC - USER REFERENCE GUIDE 4.0

Бренд: Red Hat Страницы: 92

Lancast Media Converter 7000

Бренд: Cabletron Systems Страницы: 108

Бренд: Teltone Страницы: 65

dc5750 - Microtower PC

Бренд: Promise Technology Страницы: 114

Active Management Technology v4.0

Бренд: Intel Страницы: 143

REGISTRYBOOSTER

Бренд: UNIBLUE Страницы: 3

Бренд: UNIBLUE Страницы: 4

Бренд: Sun Microsystems Страницы: 24

Бренд: FieldServer Страницы: 17

NETWORK - USER 1.2

Бренд: Red Hat Страницы: 64

COLDFUSION MX 61 - CONFIGURING AND ADMINISTERING COLDFUSION...

Бренд: MACROMEDIA Страницы: 168

B DLTSAGE INTEGRATION

Бренд: Tandberg Data Страницы: 36

SSD ULTRA320 SCSI 3.5" DC-000255

Бренд: SanDisk Страницы: 3

SCX 6322DN - B/W Laser - All-in-One

Бренд: Samsung Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды