Juniper JUNOSE 11.1.X MULTICAST ROUTING Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 270

background image

host1(config-if)#

ip block-multicast-sources

■

Use the

no

version to restore the default behavior of creating mroutes on received

multicast packets.

■

See ip block-multicast-sources.

Limiting Interface Admission Bandwidth

Interface-level multicast admission control is performed when an OIF on the interface
is added to the mroute for a given (S,G) multicast data stream and the multicast
bandwidth map contains a

set admission-bandwidth

action for that (S,G).

When enabled, the admission-bandwidth for a particular (S,G) is read from the
multicast bandwidth map and recorded in the mroute when the (S,G) mroute is
created. When an OIF is subsequently added to the mroute, the OIF is blocked from
forwarding data if the additional bandwidth contributed by the (S,G) would exceed
the admission-bandwidth limit for the interface.

CAUTION:

Before you can limit interface-level admission bandwidth, you must first

create a bandwidth map. See “Defining a Multicast Bandwidth Map” on page 10 for
details.

Enabling Interface Admission Bandwidth Limitation

You can use the

ip multicast admission-bandwidth-limit

command to enable

multicast admission control on interfaces (including dynamic IP interfaces) that are
configured to run IGMP. You can also use this command on a PIM (sparse-mode,
dense-mode, or sparse-dense-mode) interface if IGMP is configured on the interface
(including the

ip igmp version passive

command).

ip multicast admission-bandwidth-limit

■

Use to limit bandwidth for an interface that accepts IGMP groups.

■

Example

host1:boston(config-if)#

ip multicast admission-bandwidth-limit 2000000

■

Use the

no

version to remove the bandwidth limitation for the interface.

■

See ip multicast admission-bandwidth-limit.

OIF Interface Reevaluation Example

If you change the admission bandwidth for an interface, all mroutes with that interface
as an OIF are reevaluated as follows:

■

If the bandwidth limit is increased, blocked OIFs may become unblocked. If the
interface is a blocked OIF on multiple mroutes, the order in which the mroutes
are visited, and which (S,G) streams become unblocked, is not specified.

26

■

Blocking and Limiting Multicast Traffic

JUNOSe 11.1.x Multicast Routing Configuration Guide

«
...
46
47
48
49
50
...
»

Содержание JUNOSE 11.1.X MULTICAST ROUTING















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X MULTICAST ROUTING

WORKCENTRE C2424

Бренд: Xerox Страницы: 12

WorkCentre M118

Бренд: Xerox Страницы: 25

CRESTRON-APP-SSTV

Бренд: Crestron Страницы: 28

Бренд: Alphasmart Страницы: 4

MOBILE SECURITY 2010 FOR ANDROID

Бренд: F-SECURE Страницы: 20

Document centre 490

Бренд: Xerox Страницы: 102

Veritas CommandCentral 5.1

Бренд: Symantec Страницы: 52

Бренд: Seagate Страницы: 2

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 7

Studio Manager v.2

Бренд: Yamaha Страницы: 11

Studio Manager v.2

Бренд: Yamaha Страницы: 15

VL Visual Editor

Бренд: Yamaha Страницы: 23

TOOLS for MY16-mLAN

Бренд: Yamaha Страницы: 24

TOOLS for TYROS

Бренд: Yamaha Страницы: 36

Бренд: Silicon Image Страницы: 36

Бренд: Adaptec Страницы: 133

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды