Jungheinrich ETX 513 Скачать руководство пользователя

Страница: 293 / 408

Automatic horizontal and vertical destination approach (

)

Requirements

– Prepare the truck for operation, see page 139 or see page 140.
– The attachment must be in the correct position. Note the symbols in the driver's

display. If necessary push / turn the attachment to the correct home position.

– The truck is located in the set aisle and is automatically guided. An incorrect aisle

is indicated in the driver's display with the "warning" symbol.

– Enter the storage location destination, see page 284.

Procedure

• Press the deadman button (18).
• Set the travel direction switch (105) to

the required direction:
• Push the travel direction switch (105)

left = Travel in drive direction

• Push the travel direction switch (105)

right = Travel in load direction

• Slowly apply the accelerator pedal (20).
• The industrial truck begins automatic

horizontal

and

vertical

destination

approach.

Truck movement can be interrupted by
releasing the accelerator pedal (20) or
by

applying

the

EMERGENCY

DISCONNECT switch (9).

• After the warehouse location is reached:

• The

"Truck

horizontally

positioned“ (210) symbol appears in
the driver's display.

• The truck stops.
• Lifting or lowering stops automatically.
• The "Lift“ or "Lower" symbol (227,226)

goes out.

The horizontal and vertical position of the
warehouse location has now been reached.
The operator can start to stack and retrieve goods.

226

227

112

113

208

209

210

112

113

105

223

For marker detection the driver's display also shows the "Light button on reflector"
symbol (223) when the storage location has been reached.

291

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Результаты поиска

Содержание ETX 513

Отзывы:

Похожие инструкции для ETX 513

Бренды по названию

Популярные бренды

Jungheinrich ETX 513, Руководство по эксплуатации

Результаты поиска

Содержание ETX 513

Отзывы:

Похожие инструкции для ETX 513

Бренды по названию

Популярные бренды