Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 157 / 408

background image

Braking with the coasting brake (

t

)

Procedure

• Do not apply the accelerator pedal (20)

while travelling.
The accelerator pedal (20) reverts to the
neutral position.

The truck brakes via the traction controller.

18

20

19

105

Braking with the brake pedal (

t

)

Procedure

• Press down on the brake pedal (19) until you reach the required deceleration.

The truck decelerates depending on the position of the brake pedal (19).

Braking with the reversing brake (

t

)

Procedure

• During travel, set the travel direction switch (105) to the opposite direction.

The truck brakes regeneratively via the traction controller until it starts to move in the
opposite direction. This method reduces energy consumption. Energy is recovered,
which is controlled by the traction current controller.

Braking with the deadman button (

o

)

Procedure

• During travel, take your foot off the deadman button (18).

Z

This method of braking only acts as a parking brake and not as a service brake.

The truck brakes to a halt.

155

04.19 en-GB

«
...
155
156
157
158
159
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: Presto Lifts Страницы: 29

PPS2200-62NFO-21

Бренд: Presto Lifts Страницы: 31

Бренд: Jungheinrich Страницы: 229

Бренд: Jungheinrich Страницы: 250

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды