Jungheinrich ETX 513 Скачать руководство пользователя

Страница: 22 / 408

Steering

– Extremely smooth steering with threephase drive system (sturdy and

maintenance-free threephase motor with no wear parts).

– The steering wheel is integrated in the control panel. The position of the steered

drive wheel is shown in the driver's display. The maximum steer angle is ± 90°.

– In rail guidance mode the drive wheel is set to the straight-ahead position by

pressing a button. Manual steering is deactivated in this mode (

– When wire guidance mode is activated, the steering is assumed by the truck

controller when the guide wire is detected. Manual steering is deactivated in this
mode (

Controls and displays

– Ergonomic controls ensure fatigue-free operation for sensitive application of the

travel and hydraulic operations.

– Soft keys to control functions (attachment traverse, fork carriage rotate ...) and

menus.

– Colour driver's display unit for all important driver information such as steering

wheel position, overall lift, truck status reports (e.g. faults), service hours, battery
capacity, time and wire guidance status etc..

– Control panel with adjustable height and depth (

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Результаты поиска

Содержание ETX 513

Отзывы:

Похожие инструкции для ETX 513

Бренды по названию

Популярные бренды

Jungheinrich ETX 513, Руководство по эксплуатации

Результаты поиска

Содержание ETX 513

Отзывы:

Похожие инструкции для ETX 513

Бренды по названию

Популярные бренды