Jungheinrich ETX 513 Скачать руководство пользователя страница 223 | Manualshive

Страница: 223 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 223

WARNING!

An unsecured truck can cause accidents

Parking the truck on an incline or with a raised load handler is dangerous and is
strictly prohibited.

u

Always park the truck on a level surface. In special cases the truck may need to be
secured with wedges.

u

Always fully lower the mast and forks.

u

Select a place to park where no other people are at risk of injury from lowering
forks.

WARNING!

If the brakes are not working, place wedges underneath the wheels of the truck to
prevent it from moving.

95

8

9

183

24

181

181

182

Activating the load wheel brake

Requirements

– Load wheel brakes released.
– Park the truck securely.

Procedure

• Use wedges to prevent the truck from moving.
• Activate the drive wheel brake, see page 215.
• Remove the setscrews from the thread holes (181) of the load wheel brake.
• Store the setscrews in a plastic bag.
• Seal the plastic bag with adhesive tape.

221

04.19 en-GB

«
...
221
222
223
224
225
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды