Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 199 / 408

background image

Procedure

• Press the deadman button.
• Drive carefully up to the storage location.
• Set the attachment to the "front lifting" position:

• Do not press the deadman button.
• Traverse the attachment to the centre position, see

• Rotate the fork carriage so that it is at right angles (90°)

to the truck, see page 175.

• Press the deadman button.
• Raise the load handler so that the load can be taken to

the storage location without striking any objects.

• Carefully bring the load to its storage location.
• Carefully lower the load handler so that the forks are clear of the load.

Z

Avoid depositing the load suddenly to avoid damaging the load, load handler and
the rack.

• Make sure you can see behind you and that you have sufficient space to move.
• Carefully remove the load handler from the load.
• Do not press the deadman button.
• Slowly traverse and rotate the forks until they are in the home position, see

page 182 or see page 183.

• Press the deadman button.
• Fully lower the load handler.

The load has been deposited correctly.

90˚

197

04.19 en-GB

«
...
197
198
199
200
201
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: woodmizer Страницы: 26

Бренд: Hyster Страницы: 21

Бренд: Hyster Страницы: 25

Бренд: Hyster Страницы: 25

Бренд: Hyster Страницы: 21

Бренд: Hyster Страницы: 21

Бренд: Hyster Страницы: 124

Бренд: Xilin Страницы: 18

Бренд: Hyster Страницы: 19

Бренд: Global Industrial Страницы: 6

Бренд: Versalift Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды