Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 98 / 408

background image

Hazardous area

WARNING!

Risk of accidents / injury in the hazardous area of the truck

The hazardous area is defined as the area in which a person is at risk due to truck
movement, lifting operations, the load handler (e.g. forks or attachments) or the load
itself. This also includes areas which can be reached by falling loads or lowering
operating equipment.

u

Instruct unauthorised people to leave the hazardous area.

u

Give a warning signal with plenty of time for people to leave.

u

If unauthorised personnel are still within the hazardous area stop the truck
immediately.

Safety devices and warning labels

Safety devices, warning signs (see page 46) and warning instructions in the present
operating instructions must be strictly observed.

Z

Warnings and notices such as capacity charts, strap points and data plates must be
legible at all times. Replace if necessary.

WARNING!

Accident risk due to removing or disabling of safety devices

Removal or disabling of safety devices such as the Emergency Disconnect switch,
deadman switch, horn, warning lights, gates, protective window, covers, etc. may
result in accidents and injuries.

u

Report any defects immediately to your supervisor.

u

Tag out and decommission a faulty lift truck.

u

Only return the truck to service when you have identified and rectified the fault.

96

04.19 en-GB

«
...
96
97
98
99
100
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: Big Joe Страницы: 28

Бренд: Baoli Страницы: 102

Бренд: Still Страницы: 392

Бренд: RC4WD Страницы: 27

Бренд: CombiLift Страницы: 73

CP LIGHT evo 030

Бренд: ARMANNI Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды