manualshive.com logo in svg

Jungheinrich ETX 513, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ETX 513 Скачать руководство пользователя страница 350

267

266

268

95

Checking the hydraulic oil level and replenishing if necessary

Requirements

– Park the truck on a level surface.
– Fully lower the load handler.
– Prepare the truck for maintenance and repairs (see page 328).
– Open the drive compartment cover (95), see page 330.

Procedure

• Unscrew  the  breather  (266)  and  dipstick  (267)  clockwise  out  of  the  hydraulic

reservoir (268).
The  hydraulic  oil  level  should  be  between  the  "MIN"  and  "MAX"  marks  on  the
dipstick (267).

WARNING!

Overfilling  the  hydraulic  reservoir  can  result  in  accidents  and  damage  the
environment

The  hydraulic  oil  should  not  be  above  the  "MAX"  marking  on  the  dipstick,  as  any
escaping  oil  can  damage  the  environment  and  cause  truck  malfunctions.  The
escaping hydraulic oil could run under the drive wheel for example and extend the
truck's stopping distance, as well as affect its handling.

u

Add hydraulic oil only as far as the "Max" marking on the dipstick.

u

Remove any spilled hydraulic immediately with an appropriate bonding agent.

u

The bonding agent / hydraulic oil mixture must be disposed of in accordance with
regulations.

348

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды