Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 373 / 408

background image

1.2.2

Inspection contents

The following points must be checked:

1.2.2.1

Standard equipment

Brakes

The secure seating and function of the microswitches and sensors and for damage
The secure seating of the connections and cables and for damage
Brake linings for wear and damage

Electrical system

Cables and engine are secure and for damage
Warning and safety devices are in accordance with the operating instructions
Function of display and controls
The function of the emergency disconnect and for damage
Contactors and/or relays for wear and damage
Note: If the service seal is damaged, check the internal main current fuses for damage
and check their ratings. Attach a new seal to the combined control unit after the test.
The electric wiring for damage (insulation damage, connections) and the fuse ratings
The presence of the service seal on the combined control unit and for damage
Electrostatic discharge strap or chain is present and for damage

Power supply

The function of the battery latch and battery attachment and for damage
The function and secure seating of the battery connector and for damage

Travel

The function of the "travel" controls and that the labels are legible and complete
The function of the deadman switch and for damage
The function and secure seating of the sensors and for damage
Drivetrain bearings for wear and damage
Transmission for noise and leaks
Wheel bearings and attachment for wear and damage
Wheels for wear, damage and secure mounting

Chassis/structure

Industrial truck for damage and leaks
The secure seating of the chassis and screw connections and for damage
The battery rollers and any support rubber to ensure presence and function
Labels are legible, complete and plausible
Driver's seat for damage
The driver's cab is securely attached
The secure seating of the driver's seat and the function of the adjustment mechanism

371

04.19 en-GB

«
...
371
372
373
374
375
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: Gude Страницы: 6

Бренд: Manitou Страницы: 106

Бренд: EKKO Страницы: 26

Бренд: EKKO Страницы: 27

Бренд: Kellfri Страницы: 8

Бренд: WIFO Страницы: 32

Бренд: SilverStone Страницы: 35

Бренд: SilverStone Страницы: 36

FORGED TINE B808PP

Бренд: albutt Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды