Jungheinrich ETX 513 Скачать руководство пользователя страница 342 | Manualshive

Страница: 342 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 342

4.5

Lift chain servicing

WARNING!

Non-lubricated and incorrectly cleaned lift chains can cause accidents

Lift chains are safety-critical parts. They must not contain any serious contamination.
Lift chains and pivot pins must always be clean and well lubricated.

u

Lift chains should only be cleaned with paraffin derivatives e.g. petroleum or diesel
fuels.

u

Never clean chains with steam jet high pressure cleaners, cold or chemical
cleaning agents.

u

Immediately after cleaning, dry the lift chain with compressed air and apply a chain
spray.

u

Always lubricate a chain when it is discharged.

u

Lubricate a lift chain with particular care around the pulleys.

WARNING!

Solvents (e.g. paraffin derivatives) can be hazardous

u

Solvents can cause irritation if they come into contact with the skin. Rinse any
affected areas thoroughly.

u

If they come into contact with the eyes rinse them immediately with flowing water
and call for a doctor.

u

Wear personal protective equipment (e.g. safety boots, hi-vis jacket, goggles, work
gloves etc.) when working with solvents.

Z

The intervals stated in the service checklist apply to normal duty use. More
demanding conditions (dust, temperature) require more regular lubrication of the lift
chains. The prescribed chain spray must be used in accordance with the
instructions. Applying grease externally will not provide sufficient lubrication of the lift
chains.

4.6

Lubricate the lift chains, clean and grease the contact surfaces in

the mast sections

WARNING!

Accident risk during maintenance work on elevated maintenance points

There is danger of falling and trapping when performing maintenance work on
elevated maintenance points (for example lubricating the mast).

u

Wear personal protective equipment.

u

Use a working platform, lifting stage or safety ladder.

u

Do not use leaning ladders.

u

Do not stand under the load handler.

Requirements

– Industrial truck parked on a level surface.
– Wear personal protective equipment.

Tools and Material Required

– Working platform, lifting stage or safety ladder

340

04.19 en-GB

«
...
340
341
342
343
344
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды