Jungheinrich ETX 513 Скачать руководство пользователя страница 251 | Manualshive

Страница: 251 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 251

8.2.3

Individual movement of the telescopic table fork tines (

o

)

WARNING!

The load can fall down if the telescopic forks do not traverse correctly

If a single telescopic fork tine moves when the loads on the two telescopic forks are
overlapping, this can cause the load to fall. Always take into account the load on the
telescopic table when choosing the telescopic forks.
An individual telescopic fork tine must not be chosen when the load on the two
telescopic forks is overlapping, i.e. when laden with a wire box.

u

Always take into account the load on the telescopic table when choosing the
telescopic forks.

u

Do not move an individual telescopic fork when the load on both telescopic forks is
overlapping.

NOTICE

Risk of material damage to the telescopic forks

The telescopic forks must not be used to push or press loads.

249

04.19 en-GB

«
...
249
250
251
252
253
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды