Jungheinrich ETX 513 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 83

Safety procedures for charging batteries

Requirements

– Park the truck securely, see page 180.
– Expose the battery, see page 78.
– Switch off the charger.
– Correct charging program set on charger.

Procedure

• Disconnect the battery (14).
• Connect the charge cable of the battery

charging

station

to

the

battery

connector (14).

CAUTION!

When charging, the tops of the battery cells
must  be  exposed  to  provide  sufficient
ventilation.  Do  not  place  any  metal  objects
on  the  battery.  Before  charging,  check  all
cables  and  plug  connections  for  visible
signs of damage.

NOTICE

Risk of fire and material damage

The charger must be adapted to the battery
in terms of voltage and charge capacity. It is
essential to follow the safety regulations of
the

battery

and

charger

station

manufacturers.
• Switch on the charger.
• Charge the battery (98) in accordance with the battery and charging station

manufacturer's instructions.

The battery is charged.

15

14

98

81

04.19 en-GB

«
...
81
82
83
84
85
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды