Jungheinrich ETX 513 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 143

Procedure

• In the driver's display (107) you will be

prompted to enter your 5 digit access
code. Enter the access code, to do this:

Z

Unless the correct access code is
entered, none of the truck's functions will
work.
• Press the "Select" button (147) in the

cursor field.

• Enter your 5 digit access code with the numerical keypad (112). The cursor

keys (146,148) can be used to enter each digit of the 5-digit access code:
- Cursor key (148): one digit forward.
- Cursor key (146): one digit back.

• Press the "CE" key (150) to cancel entering the 5 digit access code.
• Press "OK" (149) and confirm the access code entry.

Z

If no travel, steer or hydraulic operations are performed within a factory-set
interval, the driver's display (107) will prompt you again to enter the 5 digit access
code with the numerical keypad (112). In addition all truck functions are inhibited.
When you have entered the access code the truck will be operational. The interval
can be changed by the manufacturer's customer service department.

The truck is now operational. The steering is in the straight-ahead position.

107

147

149

148

146

150

112

141

04.19 en-GB

«
...
141
142
143
144
145
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды