Jungheinrich ETX 513 Скачать руководство пользователя

Страница: 125 / 408

Symbol and meaning

Function

Optional equipment

“Work lights / fan menu
change” display

Changes the menu to “work lights / fan
menu change” functions.

“Work lights / fan menu
change” button

Activates the work lights / fan menu
change.

“Overhead guard work
lights” display

Indicates that the overhead guard work
lights can be switched on / off.

“Overhead guard work
lights” button

Switches the overhead guard work lights
on and off.

"Operator position
lighting" display

Indicates that the operator position
lighting can be switched on / off.

"Operator position
lighting" button

Switches the operator position lighting on
and off.

“Overhead guard strobe”
display

Indicates that the strobe on the overhead
guard can be switched on / off.

“Overhead guard strobe”
button

Switches the overhead guard strobe on
and off.

"Spotlight positioning"
display

Indicates that the spotlight can be
switched on / off.

"Spotlight positioning"
button

Switches the spotlight on and off.

"Reverse lights" display

Indicates that the reverse lights can be
switched on / off.

"Reverse lights" button

Switches the reverse lights on and off.

“Fan” display

Indicates that the fan can be switched
on / off.

"Fan" button

Switches the fan on and off.

"Left camera" display

Indicates that the pictures from the left
camera can be shown on the monitor.

"Left camera" button

Switches the monitor to the left camera.

"Right camera" display

Indicates that the pictures from the right
camera can be shown on the monitor.

"Right camera" button

Switches the monitor to the right camera.

"Weighing system display
zero setting" display

Indicates that the weight measurement
display can be set (tared) to zero, see
page 292.

"Weighing system display
zero setting" button

Sets the weight measurement to zero.

123

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Результаты поиска

Содержание ETX 513

Отзывы:

Похожие инструкции для ETX 513

Бренды по названию

Популярные бренды

Jungheinrich ETX 513, Руководство по эксплуатации

Результаты поиска

Содержание ETX 513

Отзывы:

Похожие инструкции для ETX 513

Бренды по названию

Популярные бренды