Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 132 / 408

background image

3.3.1

Adjusting the driver’s seat

Z

The procedure for adjusting the driver’s seat applies to standard models. For other
models, follow the manufacturer’s setting instructions. When adjusting, ensure that
all controls are within easy reach.

WARNING!

Risk of accidents and damage to health

An incorrectly adjusted driver’s seat can result in accidents and damage to health.

u

Do not adjust the driver’s seat while travelling.

u

The driver’s seat should lock in position after adjustment.

u

Check and adjust the individual driver’s seat setting before starting to use the
truck.

u

Hold the weight setting lever (142) only by the recess, do not reach through
underneath the lever.

Adjusting the driver's weight

NOTICE

To  achieve  optimal  seat  cushioning  the
driver’s  seat  must  be  set  to  the  driver’s
weight.
Set  the  driver's  weight  when  the  seat  is
unoccupied.
Seat cushioning setting range: 50 kg - 130
kg.

Procedure

• Pull the weight adjustment lever (142) in

the arrow direction until you reach the
required weight on the scales.

• Pull the weight adjustment lever (142) in the direction of the arrow as far as the

stop and then return it.
The weight setting is set to a minimum value.

• Restore the weight adjustment lever (142) to its original position.

The driver’s weight is now set.

141

142

143

130

04.19 en-GB

«
...
130
131
132
133
134
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: AVANT Страницы: 36

VERACITOR GCC030VX

Бренд: Yale Страницы: 206

Бренд: Noblelift Страницы: 16

Бренд: Noblelift Страницы: 16

Бренд: Noblelift Страницы: 24

Бренд: Noblelift Страницы: 24

Бренд: Noblelift Страницы: 24

Бренд: Noblelift Страницы: 28

Бренд: Noblelift Страницы: 28

Бренд: Noblelift Страницы: 31

Бренд: Noblelift Страницы: 32

Бренд: Noblelift Страницы: 33

Бренд: Noblelift Страницы: 60

FE4P16-20 Q Series

Бренд: Noblelift Страницы: 67

Бренд: Noblelift Страницы: 105

TIGRIP TKG 1,0 vh

Бренд: CMCO Страницы: 49

PANTHER MAXI AC

Бренд: logitrans Страницы: 28

Бренд: SolidHub Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды