Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 136 / 408

background image

4

Industrial Truck Operation

4.1

Safety regulations for truck operation

Travel routes and work areas

Only use lanes and routes specifically designated for truck traffic. Unauthorised third
parties must stay away from work areas. Loads must only be stored in places
specially designated for this purpose.
The truck must only be operated in work areas with sufficient lighting to avoid danger
to personnel and materials. Additional equipment is necessary to operate the truck in
areas of insufficient lighting.

DANGER!

Do not exceed the permissible surface and spot load limits on the travel routes.
At blind spots get a second person to assist.

NOTICE

Loads must not be deposited on travel or escape routes, in front of safety
mechanisms or operating equipment that must be accessible at all times.

Travel surface

The travel surface on which the truck is to be used on must be suitably maintained in
order to provide the required traction for travel, steering and braking under the
prevailing ambient conditions.

The  details  on  the  truck  data  plate  assume  a  level  and  dry  travel  surface.  Other
ground  surfaces  may  have  a  negative  affect  on  the  stability  of  the  truck.  They  will
result  in  a  modification  of  the  rated  performance  (e.g.  speed  reduction  etc.)  of  the
truck.

134

04.19 en-GB

«
...
134
135
136
137
138
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: FARMTECH Страницы: 22

VERACITOR GCC030VX

Бренд: Yale Страницы: 206

Бренд: cascade corporation Страницы: 4

QFM Push/Pull E Series

Бренд: cascade corporation Страницы: 14

Бренд: cascade corporation Страницы: 12

Bulk Box Handler Series

Бренд: cascade corporation Страницы: 22

Бренд: cascade corporation Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды