Jungheinrich ETX 513 Скачать руководство пользователя страница 361 | Manualshive

Страница: 361 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 361

G Maintenance, Inspection and Changing of

Maintenance Parts Requiring

Replacement

WARNING!

Lack of maintenance can result in accidents

Failure to perform regular maintenance and inspections can lead to truck failure and
poses a potential hazard to personnel and equipment.

u

Thorough and expert maintenance and inspections are among the most important
requirements for the safe operation of the industrial truck.

NOTICE

The  application  conditions  of  an  industrial  truck  have  a  considerable  impact  on
component  wear.  The  following  service,  inspection  and  replacement  intervals  are
based  on  single-shift  operation  under  normal  operating  conditions.  The  intervals
must  be  reduced  accordingly  if  more  stringent  requirements  are  placed  on  the
equipment,  e.g.,  use  in  conditions  of  extreme  dust,  temperature  fluctuations  or
multiple shifts.

u

To prevent damage due to wear, the manufacturer recommends an on-site
application analysis to agree on appropriate intervals.

The following chapter defines the tasks to be performed, the respective intervals to
be observed and the maintenance parts for which replacement is recommended.

359

04.19 en-GB

«
...
359
360
361
362
363
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды