Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 193 / 408

background image

5.3.1

Raising a load unit from the side

Requirements

– Prepare the truck for operation, see page 139 or see page 140.
– Load unit correctly palletised.
– Fork spread for the pallet checked and adjusted if necessary, see page 184.
– Load unit weight does not exceed the truck's capacity.
– Forks evenly loaded for heavy loads.
– Good ground conditions.

Procedure

• Press the deadman button.
• Drive carefully up to the storage location.
• Lower/raise the load handler so that the load can be lifted.
• Do not press the deadman button.
• Slowly insert the forks into the pallet until the fork shank

touches the load or the pallet.

Z

The load unit must not extend by more than 50 mm
beyond the fork tips.

• Press the deadman button.
• Raise the load slightly until it rests freely on the forks.
• Do not press the deadman button.
• Slowly retract the forks to the home position, see

page 182 or see page 183.

• Press the deadman button.
• Make sure you have a clear view and sufficient area to

move in.

• The load can now be transported with the truck, see

The load has been lifted correctly.

191

04.19 en-GB

«
...
191
192
193
194
195
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: KAUP Страницы: 26

Бренд: CESAB Страницы: 324

Бренд: Terex Страницы: 67

Бренд: Cascade Страницы: 12

Бренд: cascade corporation Страницы: 28

Бренд: Cascade Страницы: 14

KOOI Reachforks 20B TFE

Бренд: Cascade Страницы: 16

Бренд: cascade corporation Страницы: 58

Бренд: Cascade Страницы: 60

Бренд: Kalmar Страницы: 600

Бренд: Ravas Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды