Jacobsen ZB Series Скачать руководство пользователя страница 95

Страница: 95 / 134

en-93

MAINTENANCE AND LUBRICATION 8

8.17 HYDRAULIC HOSES __________________________________________________

Always lower the cutting units to the ground, disengage all drives, engage parking brake, stop the engine and

remove the key before you inspect or disconnect hydraulic lines or hoses.

Check visible hoses and tubes each day. Look for wet hoses or oil marks. Replace worn or damaged hoses and

tubes before you operate the mower.

The replacement tube or hoses must follow the same path as the original hose. Do not move the clamps,

brackets and cable-ties to a new location.

Completely inspect all tubes, hoses and connections in accordance with the maintenance chart.

IMPORTANT: If the hydraulic fluid becomes dirty, damage to the hydraulic system can occur.

Before you disconnect any hydraulic component, clean the area around the fittings and the ends of the hoses to

stop the entry of dirt into the system.

Before you disconnect any hydraulic component, tag or mark the location of each hose then clean the area

around the fittings.

To stop the entry of dirt into the system when you disconnect the component, be prepared to assemble plugs or

caps to the ends of hoses and open ports. Clean any hydraulic fluid that spills.

Make sure “O” rings are clean and hose fittings are correctly installed before you tighten.

Prevent the hose twist. The twisted hoses can cause the hose connections to loosen as the hose moves while

you operate the mower and can cause oil leaks.

The hydraulic hoses that are twisted or have sharp bends can decrease the oil flow and cause damage to the

hoses. The decreased oil flow can cause system problems and increase the temperature of the hydraulic fluid.

WARNING

To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the

paper or cardboard to find leaks.

The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered

your skin, a doctor must remove the hydraulic fluid surgically within a few hours or gangrene can

occur.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды