Jacobsen ZB Series Скачать руководство пользователя страница 55

Страница: 55 / 134

en-54

6 OPERATION

6.4 TO FIT THE CUTTER DECKS TO THE MACHINE ____________________________

Front deck mounting.

1. Make sure the hydraulic hoses are plugged to prevent loss of hydraulic oil. Start the engine and lower the

lift arms (A) to the ground. Stop the engine and remove the ignition key.

2. Position the flail deck in front of the vehicle and align the lift arms with the unit mounting bracket.
3. Apply a small amount of grease to pin (B) and then slide the pins through the lift arm and flail mounting

bracket.

4. Fasten pin (B) in place with quick release pins (C).
5. Remove the hose plugs and fit the hoses to the flail brake valve on the cutting unit.

NOTICE

For height of cut adjustments see section 7.5.1 and 7.5.2

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды