Jacobsen ZB Series Скачать руководство пользователя страница 46

Страница: 46 / 134

en-46

5 CONTROLS

5.2.Z.1

WARNING MAXIMUM SLOPE ANGLE EXCEEDED _______________________

When this screen is shown, the maximum permitted slope angle has been

exceeded.

Press the button below the



to confirm the fault.

5 3.

TRACTION PEDAL ___________________________________________________

The traction pedal is found on the right side of the footplate.

•

Carefully press the top (A) of the foot pedal to reach the forward
speed that you need.

•

To stop - Carefully return the foot pedal to the Neutral position.

•

To move in the reverse direction press the bottom (B) of the foot
pedal.

5 4.

STEERING TILT CONTROL ____________________________________________

Tilt the column backward or forward to the correct position. Release the

small foot pedal to lock the steering column in position.

5 5.

HORN _____________________________________________________________

The horn button is on the control panel. If the lighting kit is fitted, the horn is

also found on the end of the indicator stalk (Section 5.10).

0°

Slopes > = 25°

in either x or y

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды