Jacobsen ZB Series Скачать руководство пользователя страница 22

Страница: 22 / 134

en-22

5 CONTROLS

5.2.A STARTER KEY SWITCH ______________________________________________

Turn the starter key to the right to the 'start' position to start the engine. When

the engine starts, release the key and allow to return automatically to the 'on'

position to run.

NOTE. There can be a time delay before the engine starts, it depends on

the engine temperature while the glow plugs operate automatically.

5.2.B THROTTLE CONTROL ROTARY ________________________________________

Rotate the control to the right to increase the engine speed and toward the left

to decrease the engine speed.

NOTE: Operate the engine at full speed.

5.2.C PARKING BRAKES___________________________________________________

Move the orange button back and press the switch to engage the parking

brake.

When the engine is stopped, the parking brake is applied.

To release the parking brake, press the opposite end of the switch.

The parking brake icon

is displayed on the visual display screen when

engaged.

DO NOT apply the brake while the machine is in motion.

5.2.D TRANSPORT LOCK SWITCH __________________________________________

Engages the wing unit locks for transport

The wing unit lock icon

is displayed on the visual display screen when

engaged.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды