Jacobsen ZB Series Скачать руководство пользователя страница 104

Страница: 104 / 134

en-102

9 PROBLEM SOLVING

9.1 ENGINE PROBLEM DIAGNOSTICS

The Engine is difficult to start

Cause

Action

The fuel is thick and does

not flow.

Check the fuel tank and fuel filter.

Remove any contamination from the

fuel system.

Clean the fuel filter with kerosene.

Air or water mixed in fuel

The fuel system is a pressure type.

Air in the system will cause a

problem. Bleed the Fuel System.

To get correct fuel injection pressure,

check carefully for loose fuel line

couplings and loose cap nut.

Loosen the joint bolt stop, fuel filter

and air vent screws of fuel injection

pump to remove all the air in the fuel

system.

The Engine oil becomes

thick in cold weather and

engine cranks slowly.

Change the grade of oil according to

the average temperature.

The Battery is

discharged and the

engine will not crank

Charge the battery.

In the winter, always remove the

battery from the machine. Keep the

battery charged and store in a dry,

safe environment.

Loss of Power

Cause

Action

No fuel.

Check the fuel system.

Moving parts at more

than operating

temperature.

Check lubricating oil system.

Make sure that the lubricating oil filter

flow is not decreased.

A dirty filter element can cause loss of

lubrication. Change the filter element.

The air cleaner is dirty.

Clean the filter element every 100

hours of operation.

Injection pump wear.

Use the correct grade of fuel. Low

grade fuel will cause the fuel pump to

wear. Only use the specified Diesel

fuel.

The Engine stops

Cause

Action

There is no Fuel

Check the fuel tank and fill with fuel.

Check the fuel system for air leaks.

Bad Nozzle

If necessary, replace the nozzle.

Moving parts at more

than operating

temperature.

Not enough lubrication.

Check amount of engine oil with oil

level gauge.

Check lubricating oil system.

The oil filter cartridge must be

replaced at every second oil change.

Dirty Smoke or carbon increase on the Exhaust

Cause

Action

Wrong fuel.

Only use Diesel fuel specified in

specification section.

Bad Nozzle.

If necessary, replace the nozzle.

Engine must be stopped immediately

Cause

Action

The colour of The

exhaust turns dark.

Check the fuel system and the fuel

injection nozzle.

The bearings are at

more than operating

temperature.

Check the lubricating system.

The oil-temperature

light is illuminated.

Check the lubricating system.

Check the function of the relief valve

in the lubricating system.

Check the pressure switch.

Check the fuel filter base gasket.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды