Jacobsen ZB Series Скачать руководство пользователя страница 107

Страница: 107 / 134

en-105

QUALITY OF CUT 10

NOTE:

The Arrow indicates direction of travel.

“Step cutting” occurs when the grass is cut higher

on one side. The cause is mechanical wear or

incorrect setting of the roller or deck caster.

Possible Cause

Correction

The HOC (height-of-cut) settings are different on the

side of one cutting unit or the cutting cutter decks are

set at different heights.

Check HOC adjustment of cutting units. (Refer to

Parts and Maintenance Manual.

Worn roller bearings or deck caster wheels.

Check and replace the roller bearings, deck caster

wheels.

Cutting unit movement is decreased.

Check and remove the cutting unit movement limit.

Changes in turf density.

Change the direction of cut.

The Machine ride height is not equal from side to side.

Check and adjust the tyre pressure. (Refer to Parts

and Maintenance Manual.

Cutting unit height is not equal from side to side.

Check and adjust the mower weight distribution.

TN0221

10.2 THE STEP CUT ________________________________________________________

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды