Jacobsen ZB Series Скачать руководство пользователя страница 30

Страница: 30 / 134

en-30

5 CONTROLS

SERVICE MENU

Please note some functions require a PIN to access.

5.2.Z.14 SERVICE MENU ___________________________________________________

The button accepts the option that has the ü.

The



is moved with the up and down to select, fault log, time until

service, diagnostics, I/O diagnostics and ECU (engine Control Unit) monitor.

5.2.Z.15 FAULT LOG_______________________________________________________

Select the fault log



and accept .

5.2.Z.16 FAULT LOG_______________________________________________________

The last 50 “Faults” that the controller finds are recorded. When 50 faults are

recorded, the fault that next occurs will write over the oldest fault.

This information is got with the service tool or can be seen on the errors page of

the service menu. Press the button to select, press the button up and

down to move the ü. The errors will move with the last error at the top of the

screen.

The fault / data log function has three actions. Each fault / data log function can

contain a maximum of 50 faults. the areas included are:

The Inclinometer, records slopes of more than 22°.

The Engine, records the engine shut downs because of overheat or loss of oil pressure.

The Service, records hydraulic by-pass fault and missed service.

Service Menu

Fault Log

Time Until Service

Diagnostics

I/O Diagnostics

J1939

Service Menu

Fault Log

Time Until Service

Diagnostics

I/O Diagnostics

J1939

Fault Log

0 0 Hours

1 0 Hours
2 0 Hours

TST

™

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды