Jacobsen ZB Series Скачать руководство пользователя страница 93

Страница: 93 / 134

en-91

MAINTENANCE AND LUBRICATION 8

8.14 CHARGE THE BATTERY _______________________________________________

Read the battery charger manual for specified instructions on the operation of the charger.

When possible, remove the battery from the mower before you charge the battery. If the battery is not sealed,

check and make sure the level of the electrolyte is above the plates in all of the cells.

Make sure the battery charger is turned ‘OFF’, then connect the battery charger to the battery terminals as

specified in the battery charger manual.

Always turn ‘OFF’ the battery charger before you disconnect the battery charger from the battery terminals.

8.15 ENGINE EXHAUST ____________________________________________________

If you sense a change in the color or sound of the exhaust, stop the engine immediately. Identify the problem and

have the system repaired.

Torque all exhaust manifold hardware equally. Tighten or replace the exhaust clamps.

WARNING

Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive.

To prevent an explosion, keep any device that can cause sparks or flames away from the battery.

When the battery charger is turned on, to prevent injury, stay away from the battery. A battery that is

damaged can cause an explosion.

WARNING

The exhaust fumes contain carbon monoxide. The carbon monoxide in the exhaust fumes can increase

to dangerous levels. To protect you from carbon monoxide poisoning, inspect the complete exhaust

system every month and replace damaged components immediately.

NEVER operate the engine without enough ventilation.

The temperature of the exhaust components can be greater than 300° F (149° C).

To prevent the burns, do not touch a hot exhaust system.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды