Jacobsen ZB Series Скачать руководство пользователя страница 39

Страница: 39 / 134

en-39

5 CONTROLS

5.2.Z.44 CROSS CUT _____________________________________________________

Select cross cut



and accept

5.2.Z.45 CROSS CUT ACTIVE / INACTIVE ____________________________________

Use the button up and down to move between cross cut active and not

active.

Press the button .to accept.

Press the button to return to previous menu.

5.2.Z.46 VEHICLE SPEED _________________________________________________

Select the vehicle speed



and accept

5.2.Z.47 MAXIMUM SPEED SETTINGS MENU _________________________________

Use the button up and down to move

between transport and mow speed and creep

speed.

Press the button .to accept.

Select which transport and mow speeds are

needed in forward and reverse.

Use the button up and down to move to

the needed speed.

Press the button .to save.

Press the button to return to previous menu.

Do the procedure for creep mode.

Cross Cut

active

Pin Menu

Cruise Control

Cross Cut

Vehicle Speed

Change PIN

Pin Menu

Cruise Control

Cross Cut

Vehicle Speed

Change PIN

Max Speed Settings Menu

Transport and Mow Speed

Creep Speed

Max Speed Menu

Transport

FW 24 km/h

RVS 8 km/h

Mow FW 11 km/h

RVS 8 km/h

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды