Jacobsen ZB Series Скачать руководство пользователя страница 48

Страница: 48 / 134

en-48

5 CONTROLS

5 8.

TOW VALVE ________________________________________________________

The Tow valve is situated on the right hand side of the transmission pump.

1. To push the machine, disengage the parking brake, see section 5.8

2. Turn screw (A) located on the right side of the transmission pump three

complete turns counterclockwise. Set the steering wheel so that the rear
wheels are pointing straight ahead.

3. After pushing the machine, return the parking brake valve, see section

5.8 to its normal position and screw (A) on the pump to its operating
position.

5 9.

PARKING BRAKE RELEASE VALVE_____________________________________

The Parking Brake Release Valve is situated under the foot plate, on the right

hand side of chassis plate. The Parking Brake Release Valve is used to

release the parking brake when the engine is not in operation

The Parking brake is released with the handwheel (A) turn completely in after

you release lock wheel (B). Use the hand pump (C) to create enough pressure

to release the brakes (50 to 60 strokes will give 90 seconds of brake release).

When complete rotate the handwheel (A) completely out and lock with wheel

(B).

This method of brake release is to recover the vehicle a short distance only

and should be carried out on level ground.

5 10. LIGHTING KIT (OPTIONAL) ____________________________________________

Lighting Control Stalk

A. Push away from operator to turn the dipped beam head lights on.
B. Pull toward operator to flash the headlights.
C. Move the stalk up to indicate right turn.
D. Move the stalk down to indicate left turn.
E. Push the stalk in to sound horn.

NOTE: The Side lights will operate when the ignition is in the run position

When the lighting kit is fitted, a brake light function is available. Rear view mirrors must be fitted If brake lights are

used.

WARNING

THE FREE WHEEL FACILITY IS FOR RECOVERY PURPOSES ONLY.

Do not tow the machine for more than a few metres, or allow the machine to free wheel down slopes

even when unloading down ramps.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды