Jacobsen ZB Series Скачать руководство пользователя страница 12

Страница: 12 / 134

en-12

3 SAFETY

Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To

prevent an explosion, keep any device that can cause sparks or flames away from the battery.

Disconnect the battery charger from the power supply before you connect or disconnect the battery charger

to the battery. Wear protective clothing and use insulated tools when you service the battery.

Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged

blades, do not try to correct a damaged blade.

Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in

operation, unless the adjustment needs the engine in operation.

Carefully release the pressure from components with stored energy.

To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the paper

or cardboard to find leaks.

The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your

skin, a doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.

When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to

the correct torque. Make sure the hydraulic system is in good condition before you start the engine.

Keep the mower and the engine clean.

Allow the engine to become cool before storage and always remove the ignition key.

Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.

Replace worn or damaged parts for safety. Replace damaged or worn decals. Only use parts, accessories

and attachments approved by Jacobsen.
To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank

area.
Disconnect the battery and controller connectors before you weld on this mower.

3.1.7 When you put the mower on a trailer

Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can

carry the weight of the mower.

Use a full-width ramp to load or unload the mower on a trailer.

Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be

sent down and toward sides of trailer.

Make sure that all latches are correctly fastened.

Always ensure that all legal requirements are met when using trailers.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды