Jacobsen ZB Series Скачать руководство пользователя страница 70

Страница: 70 / 134

en-68

7 ADJUSTMENTS

7.6

GENERAL INSTRUCTIONS FOR GRAMMER SEATS _______________________

To identify seat type, slide seat forward on its runners to reveal seat label.

All The seat adjustments are to be done while the vehicle is stopped.

• After removal of the backrest cover, hold the backrest frame in position with a support before the backrest

adjuster is operated. If you do not lock the frame in position safely, the backrest frame can move forward

suddenly and can cause injury.

• Use approved GRAMMER parts.

• Only GRAMMAR approved changes are to be made to the seat. During the removal and installation of the

GRAMMER driver seat, follow the instructions supplied by the vehicle manufacturer.

• When you lift the driver seat, do not hold the covers. The covers are not a load bearing component and

injury can occur.

• Before you remove the driver seat, disconnect all plug-in connectors between the seat and the vehicle

supply network. When you replace the plug-in connectors, make sure the connectors are tight so that dust

and water does not enter.

• Fasten seat belts before operation.

• Replace the seat belt after an accident.

• After an accident with a vehicle that has seat belts installed, have the seat and seat mounting checked by

the safety

personnel.

• Check the seat fasteners to make sure that the seat is installed correctly.

• If the seat does not operate correctly, have the seat repaired in a GRAMMER workshop. Check the seat for

damage to the seat suspension and bellows or for an incorrect curve in the lumbar support.

• If you do not correct problems that occur in the seat, the seat can damage your health and increase the risk

of an accident.

• Before the vehicle is used, check the load sensor, installed in the seat, for correct operation. If the driver

leaves the seat, this sensor stops the vehicle.

• If a problem is found, you must not drive the vehicle. – INCREASED RISK OF ACCIDENT –

• Do not put the loads on to seats that have a load sensor. A load on the seat can cause the vehicle to move

and cause an accident. – INCREASED RISK OF ACCIDENT –

• If you drive the vehicle and remove the weight from the seat, the vehicle will stop.

• Do not load the bellows while there is a load on the driver seat. – RISK OF INJURY FROM BELLOWS –

• Make sure that dirt and liquids can not get inside the drivers seat.

• The driver seat is not waterproof.

• Any changes or adjustment to a GRAMMER driver seat must be done in authorised workshops by approved

personnel. The changes must follow the operation instructions and must be in compliance with all national

regulations.

• Incorrect installation and assembly hold the risk of personal injury or property damage. Your warranty will

also be invalidated.

WARNING

Risk of accident

Do not operate the locking lever when you drive.

Risk of injury

Operate the lever at the grip section, do not reach below the lever.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды