Jacobsen ZB Series Скачать руководство пользователя страница 105

Страница: 105 / 134

en-103

PROBLEM SOLVING 9

Engine Temperature above Safe Maximum.

Cause

Action

Engine oil low.

Check oil level. Fill to specified level.

The fan belt is broken or

has defects.

Change the belt or adjust the belt

tension.

Coolant low.

Fill to the specified level.

The Anti-freeze solution

is too strong.

Add clean water only or change to

coolant of the correct ratio.

The radiator screen or

radiator fins are dirty.

Clean screen or fin carefully.

The radiator or coolant

lines are dirty

Clean or replace the radiator and

parts.

The fan, radiator or

radiator cap has defects.

Replace the parts.

The Thermostat has

defects.

Check the thermostat and replace if

necessary.

The Temperature gauge

or sensor has defects.

Check the temperature with

thermometer and replace if

necessary.

Engine is operated at

more than maximum

load.

Decrease the load.

Head gasket has defects

or water leakage.

Replace the parts.

Incorrect fuel used

Use specified fuel.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды