Jacobsen ZB Series Скачать руководство пользователя страница 25

Страница: 25 / 134

en-25

5 CONTROLS

5.2.P/Q/R LIFT/LOWER SWITCHES ___________________________________________

Right Hand Wing Cutter Deck

Front Cutter Deck

Left Hand Wing Cutter Deck

To lower the cutting unit move the switch lever forward.

To raise the cutting unit move the switch lever rearwards

NOTE:

If the cutter switch is engaged when the unit is lowered the green lamp will illuminate when

the unit is below 400mm from the ground.

The yellow PTO lamp will illuminate when the cutter switch in ON. When the blades are

moving the icon on the display change to green.

If the lever is pulled momentarily rearwards the unit will raise to the cross cut position and continue to rotate for 3

seconds. Lowering the unit within 3 seconds will let the blade continue rotating without stopping.

If the lever is held and the unit lifts above the cross cut position the unit will continue to lift and the blade will stop

rotating at 400mm. The lift will stop when the lever is released.

5.2 S, T, W. X INDICATOR LAMPS_____________________________________________

Yellow lamp: Illuminates when the PTO is engaged

Green lamp: Illuminates when the Right hand cutter deck is in cutting position.

Green lamp: Illuminates when the center cutter deck is in cutting position.

Green lamp: Illuminates when the Left hand cutter deck is in cutting position.

NOTE:

The green lamps T, W and X will turn red when a deck begins to stall, See section

6.8.

5.2.Y WEIGHT TRANSFER BUTTON__________________________________________

The button will transfer weight by the hydraulic system between the drive wheels and

the cutter deck.

To adjust the amount of weight transfer manually on the lift valve. See section 7.3.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды