Jacobsen ZB Series Скачать руководство пользователя страница 124

Страница: 124 / 134

en-122

12 SPECIFICATIONS

12.3 DIMENSIONS & WEIGHTS (CAB MACHINE) _______________________________

A Overall width with all flail units down.

350 cm

137.8 In

B Width of cut with all flail units down.

326 cm

128.3 In

C Width of cut with front unit and one wing down.

243 cm

95.7 In

D Width of cut With front unit down only.

160 cm

63 In

E Maximum width transport with wing units set at 39mm height of cut.

208 cm

81.9 In

F Maximum width transport with wing deck set at maximum height of cut.

221 cm

87 In

G Maximum height.

220 cm

86.6 In

H Maximum length all units down.

376.1 cm

148.1 In

J Wheel base.

165 cm

65 In

K Wheel track front (outside to outside).

160 cm

63 In

Turning circle (curb to curb).

540 cm

212.6 In

Maximum front axle loading.

1500 kg

3307 lb

Maximum rear axle loading.

900 kg

1984 lb

Weight of machine, hydraulic tanks full, fuel tank empty plus cabin and

flail units.

2111 kg

4660 lb

Weight of Fuel.

64 kg

141 lb

Weight of Front Flail - MUC160.

160 kg

353 lb

Weight of Wing Flail - MUC100.

140 kg

309 lb

Weight of Beacon Kit LMAC531A.

3.5 kg

7.7 lb

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды