Jacobsen ZB Series Скачать руководство пользователя страница 35

Страница: 35 / 134

en-35

5 CONTROLS

5.2.Z.32 INFORMATION SCREEN TWO _______________________________________

This screen displays, engine total fuel used (liter) engine fuel rate (l/h), DPF

soot (%) and drive engine torque (%)

Press the button up and down to move between screen one and two.

Press the left side button to return to the previous menu.

5.2.Z.33 ECU MONITOR RESERVED (J1939)___________________________________

Select the J1931 Reserved



and accept

5.2.Z.34 RESERVED SCREEN ONE __________________________________________

This screens displays, engine air inlet temperature (°C), intake manifold

temperature (°C), engine torque percent (%) and engine oil pressure (KPa).

Press the button up and down to move between screen one and two.

5.2.Z.35 RESERVED SCREEN TWO __________________________________________

This screen displays, engine speed (rpm), engine throttle postion (%), engine

coolant temperature (°C) and battery voltage (Volt).

Press the button up and down to move between screen one and two.

Press the left side button to return to the previous menu.

litre

l/h

Engine Total Fuel used

Engine Fuel Rate

DSF Soot

5.3

Drive Engine Torque

°C

Engine Air Inlet T

Intake Man T

Engine Torque pct

Engine Oil Pressure

KPa

°C

rpm

Engine Speed

Engine Throttle Position

Engine Coolant T

Battery Voltage

Volt

12.2

J1939 Menu

J1939 Information

J1939 Reserved

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды