Jacobsen ZB Series Скачать руководство пользователя страница 92

Страница: 92 / 134

en-90

8 MAINTENANCE AND LUBRICATION

8.13 BATTERY ____________________________________________________________

Before you service the battery, make sure the ignition switch is in the OFF position and the key is removed.

Tighten the battery cables on the battery terminals, to prevent corrosion, apply a layer of silicone dielectric grease

to battery terminals and ends of cables. Keep the vent caps and battery terminal covers in position.

Before you do any welding operation on the mower, always

disconnect the battery cables from the battery and the connectors

from the controllers.

Confirm the battery polarity before you connect or you disconnect the

battery cables.

When you install the battery, always connect the positive (RED)

battery cable before the negative (BLACK) battery cable.

When you remove the battery, always disconnect the negative (BLACK) battery cable before the positive (RED)

battery cable.

Jump Starting the Mower

Before you try to jump-start the engine, check the condition of the drained battery.

Connect the positive (+) battery terminal of the charged battery to positive battery terminal of the drained
battery.

Connect the negative (–) battery terminal of the charged battery to frame of vehicle with the drained
battery.

When the cables are connected, start the engine on the vehicle with the good battery, then start the mower.

CAUTION

When you service the battery, always use the tools with insulation, wear protective glasses and

protective clothing.

Discard used batteries as shown in your local regulations.

WARNING

The battery contains corrosive acid. Prevent contact with the battery acid.

Always wash your hands after you service a battery.

WARNING

The battery posts, battery terminals and related accessories contain lead and lead compounds,

chemicals know to the State of California to cause cancer and other reproductive harm.

WARNING

The battery can release hydrogen gas that is explosive. To decrease the risk of an explosion, prevent

sparks near the battery. Always connect the negative jumper cable to the frame of the mower with the

drained battery.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды