Jacobsen ZB Series Скачать руководство пользователя страница 3

Страница: 3 / 134

en-3

INTRODUCTION 2

2.1

IMPORTANT__________________________________________________________

The HM600 with diesel engine is a self propelled flail mower. With hydraulic systems to power the traction drive,

the cutting unit lift and lower, the cutting unit drives and the steering.

IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high

level.

This manual is part of the machine and must stay with the machine always. The suppliers of new, or used,

machines need to keep this documentation and supply the owners with a copy.

You must use the machine to cut the grass only and not for any other purpose. The compliance with these condi

tions of the operation, service and repair specified by the manufacturer, are understood to be part of the correct

use.

ALL

operators

MUST

read through this manual and understand the Safety Instructions, controls, lubrication and

maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the machine that are not approved by the manufacturer. This type of change

can release the manufacturer from the liability for any damage or injury.

Discard of worn parts in alignment with all local environment protection regulations. Use the local systems avail

able in the country where the machine is used, for these recycled materials. When the machine is at its end of

life, there are guidelines in this manual for the removal of the machine from use.

Use only Jacobsen genuine spare parts to meet the machine type approval regulations specified by

the

European Union.

2006/42/EC

These instructions are the Original instructions confirmed by Ransomes Jacobsen Limited

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды