Jacobsen ZB Series Скачать руководство пользователя страница 76

Страница: 76 / 134

en-74

7 ADJUSTMENTS

7.9.4 ARMREST (OPTION) ______________________________________________________

The armrests can be folded up if required and the height individually adjusted.

To adjust the armrests for height, separate the round cap (see arrow) from the

cover, loosen the hexagon nut (size 13mm) and adjust the armrest to the

desired position and tighten the nut again.

7.9.5 BACKREST ADJUSTMENT (OPTION) _______________________________________

The backrest extension can be individually adjusted for height by pulling it

upwards over the various increments up to the end stop.

To remove the backrest extension, pull it over the end stop.

7.9.6 LUMBER SUPPORT (OPTION) ______________________________________________

By turning the adjustment knob (arrow) to the left or right, both the height and

curvature of the backrest cushion can be individually adjusted.

This increases both the seating comfort and the performance of the driver.

7.9.7 BACKREST ADJUSTMENT (OPTION) _______________________________________

The backrest is adjusted using the locking lever (arrow).

•

The locking lever must latch into the desired position. It should not be
possible to move the backrest into another position when it is locked.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды