Jacobsen ZB Series Скачать руководство пользователя страница 90

Страница: 90 / 134

en-88

8 MAINTENANCE AND LUBRICATION

8.11 FUEL SYSTEM ________________________________________________________

Use Diesel to B.S. EN590 or ASTM D975 (Ultra Low Sulfur)

Water separator

If water is not removed from the fuel, damage to the fuel-injection system can

occur. When the fuel filter light on the filter light module is illuminated or at

service interval, drain the water from the water separator.

Stop the engine. Open the air vent at the top of water separator.

Open the drain valve at the bottom of the water separator and drain

the water. Water will drain before the fuel. When fuel drains from the
valve, close the valve.

Close the vent at the top of the water separator.

Fuel Filter

Replace the fuel filter

a. Stop the engine.
b. Open the air valve at the top of the filter to release system pressure.
c. Remove fuel filter cartridge. Clean any fuel that spills.
d. Assemble new filter cartridge to the filter base. Tighten the cartridge

with your hand.

e. Bleed air from the fuel system.

How to bleed the air from the fuel system

After water is drained from the fuel system, fuel filter cartridge is replaced or

the fuel hoses are replaced, bleed the air from the fuel system.

a. Open the air vent at the top of the water separator.
b. Press and release the hand pump until air bubbles at separator air

vent stop and fuel starts to spill. Close the vent. Clean any fuel that spills.

c. Open the air vent on the fuel filter. Turn the ignition switch to the RUN position, but do not start the

engine. Operate the fuel pump until air bubbles at filter vent stop and fuel starts to spill. Close the air vent.
Clean any fuel that spills.

d. Start the engine. The engine will remove any air remaining in the fuel hoses.

CAUTION

The diesel fuel can damage your skin. Use gloves when you use diesel fuel.

If diesel fuel touches your skin, clean the area immediately.

CAUTION

Discard diesel fuel as shown in local safety regulations

4324674

1 Water Separator
2 Air Vent
3 Drain Valve
4 Fuel Filter
5 Air Vent
6 Fuel Pump

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды