Jacobsen ZB Series Скачать руководство пользователя страница 17

Страница: 17 / 134

en-17

DECALS 4

Description

009034920

Caution, Stay Away From Hot Surfaces.

009034880

Caution, Fan Blade, Do Not Open Or Remove The Safety Shields While The Engine Is

In Operation.

009034900

Caution, Drive Belt, Do Not Remove The Safety Shields While The Engine Is In

Operation.

4324674

Caution, Low Sulfur Diesel Fuel.

4118415

Caution, Engine Coolant Under Pressure.

009034890

Caution, Keep A Safe Distance From The Machine.

009034960

Caution, Rotating Blades.

009114380

Caution, Fasten Seat Belt.

4153197

Caution, Stop The Engine And Remove The Starter Key Before You Pressure Wash

The machine.

4170640

Caution, Stop Engine & Remove the Starter Key, Lock Deck in its Vertical Position

Before Carrying Out Maintenance Under Deck.

4164860

Caution, Hydraulic Oil.

4165644

Caution, No Step.

4361247

Decal, Seat Plate 16° (ROPS Machine)

4334846

Decal, Seat Plate 15° (Cabin Machine)

Read The Operator Manual.

Crush Hazard.

Keep A Safe Distance From The Machine.

Prevent Contact With Hydraulic-Oil Release Under Pressure. Read Operator Manual.

For Service Procedures.

Danger Of Explosion If The Battery Terminals Are Short Circuited.

Maximum Permitted Slope. (See accessories section for correct limit with different

accessories).

When The Machine Is Being Used Off Road, Whether Cutting Grass Or Not, The Seat

Belt Must Only Be Worn When A ROPS Frame Is In Place And Deployed.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды