Jacobsen ZB Series Скачать руководство пользователя страница 71

Страница: 71 / 134

en-69

ADJUSTMENTS 7

7.7

SEAT (GRAMMER MSG85 _____________________________________________

To get a good seat position to operate the machine you need to adjust the leg

reach, the backrest angle and the operator weight.

A. FRONT AND REAR ADJUSTMENT

To Adjust:

The adjusting lever (A) is on the right side of the seat. Lift the lever and the seat

can move backward and forward. When the seat is in the correct position,

release the lever to put the seat into one of the preset positions.

B. BACKREST ADJUSTMENT

To Adjust:

The position of the release lever (B) is on the left side of the seat. When the driver is on the seat, lift the release

lever to release the backrest. The backrest is spring loaded to fold on to the seat cushion. Move backward in the

seat to get the correct position for the backrest. Lower the release lever to put the seat into one of the preset

positions.

C. WEIGHT ADJUSTMENT

To Adjust:

The position of the operator weight adjust lever (C) is on the front of the seat. To change the operator weight

setting with the driver on the seat, lift and rotate the lever.

HEIGHT ADJUSTMENT

To adjust:

Adjust the height when you are on the seat. Hold the edge of the seat cushion and lower the seat. Lift when the

cushion and the suspension returns to its normal position. There are three preset positions for the seat. When the

seat has lifted to the highest position, the seat returns to its lowest position.

NOTICE

The seat has a microswitch to sense the operator is in the seat.

WARNING

When the machine has a ROPS frame or a ROPS cab, the driver must wear the lap belt that is installed

in the machine.

Содержание ZB Series







































































































































Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды

Jacobsen ZB Series, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание ZB Series

Отзывы:

Похожие инструкции для ZB Series

Бренды по названию

Популярные бренды