ICS Linker IIa Скачать руководство пользователя | Manualshive

Страница: 70 / 76

background image

69

FUNCTION: ID_CANCEL_DISABLE

FUNCTION CODE:

135

PURPOSE:

This function is used to disable ID canceling

HOW TO USE:

1.

Key up

2.

Enter the ID_CANCEL_DISABLE function code

3.

Unkey

4.

The controller sends the COMMAND ACCEPTED indication

5.

The courtesy tone speed is now the newly entered value

To keep the current setting of this function you must use the SAVE STATUSES command (command #87). This
will insure the current status of this setting will be maintained upon power up and reset.

This feature is available starting with version 1.30.1 of the Linker II / Linker IIa software.

FUNCTION: TX2 ID WITH TX1 ENABLE

FUNCTION CODE:

136

PURPOSE:

When this function is enabled TX2 will key up and ID anytime TX1 does

HOW TO USE:

1.

Key up

2.

Enter the TX2 ID WITH TX1 ENABLE function code

3.

Unkey

4.

The controller sends the COMMAND ACCEPTED indication

5.

The courtesy tone speed is now the newly entered value

When this function is enabled TX2 will key up and ID anytime TX1 does.  The jumper JP6 must be installed to
have the cw audio sent to TX2.

This feature is by default disabled.

To keep the current setting of this function you must use the SAVE STATUSES command (command #87).  This
will insure the current status of this setting will be maintained upon power up and reset.

This feature is available starting with version 1.30.1 of the Linker II / Linker IIa software.

«
...
68
69
70
71
72
...
»

Содержание Linker IIa













































































Отзывы:

Нет отзывов

Похожие инструкции для Linker IIa

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: Eaton Страницы: 6

Бренд: EasySMX Страницы: 11

Бренд: EasySMX Страницы: 8

Бренд: Velleman Страницы: 26

Бренд: Velleman Страницы: 32

Бренд: Velocity Страницы: 84

Бренд: Zeta Страницы: 44

Бренд: Velleman Страницы: 12

Бренд: Kunert Professional Страницы: 29

ZoneSense Plus AS

Бренд: Halma Страницы: 58

Бренд: Edwards & Co Страницы: 16

Бренд: Infasecure Страницы: 24

Бренд: Lumel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды