ICS Linker IIa Скачать руководство пользователя

Страница: 26 / 76

FUNCTION:

PULSE AUXILIARY 3 OUTPUT

FUNCTION CODE

PURPOSE:

Pulses the auxiliary 3 output

HOW TO USE:

1.

Key up

Enter the PULSE AUXILIARY 3 OUTPUT function code

Unkey

The controller sends the COMMAND ACCEPTED indication

The auxiliary 3 output will be pulsed.

FUNCTION:

ACTIVATE KEYPAD TEST

FUNCTION CODE:

PURPOSE:

Allows testing of users radio touch pad

HOW TO USE:

1.

Key up

Enter the ACTIVATE KEYPAD TEST function code

Unkey

The controller sends the ENTER NEXT DATA indication

Key up

Push the digit to be tested

Unkey

The controller will report which DTMF digit it heard in CW

The controller will wait for another DTMF digit to be sent. If it you wish to cancel the function key up without
sending a DTMF digit and unkey. The controller will cancel the keypad test with no acknowledge tone.

Содержание Linker IIa













































































Результаты поиска

Содержание Linker IIa

Отзывы:

Похожие инструкции для Linker IIa

Бренды по названию

Популярные бренды

ICS Linker IIa, Руководство пользователя

Результаты поиска

Содержание Linker IIa

Отзывы:

Похожие инструкции для Linker IIa

Бренды по названию

Популярные бренды