ICS Linker IIa Скачать руководство пользователя | Manualshive

Страница: 65 / 76

background image

64

FUNCTION:

FORCE CTCSS ENCODE ON

FUNCTION CODE:

125

PURPOSE:

Turns on the CTCSS encode and keeps it on

HOW TO USE:

1.

Key up

2.

Enter the FORCE CTCSS ENCODE ON function code

3.

Unkey

4.

The controller sends the COMMAND ACCEPTED indication

5.

The controller now forces on the CTCSS encode

When the CTCSS encode is forced on it will stay on independent of any other condition. The CTCSS encode will
remain on regardless of the status of the transmitters, receivers or the CTCSS encode hang time.

This function is available starting with V1.16 of the Linker IIa software.

FUNCTION:

CANCEL FORCE CTCSS ENCODE ON

FUNCTION CODE:

126

PURPOSE:

Cancels the force CTCSS encode force on

HOW TO USE:

1.

Key up

2.

Enter the CANCEL FORCE CTCSS ENCODE ON function code

3.

Unkey

4.

The controller sends the COMMAND ACCEPTED indication

5.

The controller will no longer force the CTCSS encode on

If the FORCE CTCSS ENCODE ON is active and this function is used the controller will stop forcing the CTCSS
encode to be on.  The CTCSS encode will operate according to the statuses of the CTCSS encode and the CTCSS
encode hang time.

This function is available starting with V1.16 of the Linker IIa software

«
...
63
64
65
66
67
...
»

Содержание Linker IIa













































































Отзывы:

Нет отзывов

Похожие инструкции для Linker IIa

Бренд: Caen Страницы: 20

Бренд: Lamtec Страницы: 22

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: Comet Страницы: 9

Бренд: Danfoss Страницы: 16

Consolidated 2900-40 Series

Бренд: Baker Hughes Страницы: 80

Бренд: Ros Страницы: 10

Бренд: FOR-A Страницы: 6

Бренд: turck Страницы: 45

Бренд: Thermo Scientific Страницы: 68

8040 CNC - FEATURES

Бренд: Fagor Страницы: 247

Бренд: Comunello Страницы: 13

Бренд: ZKTeco Страницы: 27

TITAN CONTROLS KRONUS 2

Бренд: Sunlight Supply Страницы: 4

Бренд: M-system Страницы: 16

MU System X Dual Amplifier

Бренд: Frequency Central Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды